Recent content by Nordlicht77

Hello I took a break and now I'm trying again I now use Orca Slicer I did the ellis setting again Have a Voron Cube printed now Unfortunately it is in size Z: 30.00 Y: 30.16 X: 29.98 I know you can set it with the Orca Sclicer, but as I see it only works XY at the same time and not...

And the setting from the motherboard You actually don't need the BIGTREETECH U2C V2.1 if you set it via USB to CAN bus bridge mode in setting for the mainboard

1.Which board are you using? 2. What does the CanBoot setting look like? 3.What does the Klipper setting look like?

It shouldn't look like this when connected to MAX31865 Please set the dip switches on the EBB2209 correctly beforehand, see documentation sensor_type:MAX31865 sensor_pin: EBBCan: PA4 spi_bus: spi1 rtd_nominal_r: 1000 rtd_reference_r: 4300 rtd_num_of_wires: 2 #rtd_use_50Hz_filter: True

For Klipper it looks like this to me Enable extra low-level configuration options Micro-controller Architecture = STMicroelectronics STM32 Processor model = STM32H723 Clock Reference = 25 MHz crystal Bootloader offset = 128 kib bootloader Communication interface = USB to CAN Bus bridge ( USB...

Hello I have now completely dismantled the printer and reassembled it with a new frame I had a frame from LDO where the nuts were very tight and couldn't come out It was changed from LDO I also ordered the set from Ali and installed all the pulleys and so on from the set The engines have been...

It's a shame that I have a printer that I haven't been able to print properly with until now I have now checked the belts again with this tool https://github.com/Diyshift/3D-Printer/tree/main/GT2%20Belt%20Tension%20Meter Then I put a second aluminum plate on top of the other aluminum plate on...

For me it looks like this under stepper_z endstop_pin : probe:z_virtual_endstop and [probe] pin = !EBBCan:gpio22 speed: 5.0 lift_speed: 5.0 samples: 2 samples_result: median sample_retract_dist: 3.5 samples_tolerance: 0.02 samples_tolerance_retries: 1 activate_gcode: ##Tap temp probing...

I have now checked the small Z belts and all the grub screws and pullies Can someone check whether there is an error in the Klipper config

Hello As I wrote before, I already set it to standard profile and nothing I'm slowly losing track too Now I just haven't checked the small z belts and the pully of Z motors and replaced the rail of x then everything should be fine I also changed drivers

Hello I have now swapped the Z rails and Y rails again and swapped the belts of xy and also checked the pullies I turned off the bed mesh Unfortunately everything happened without I looked at the middle when setting the Extrusion Multiplier and as it says on the page Minimum layer time: 0 set...

Hello Unfortunately the same result Have it again now Extruder calibration First Layer Squish Extrusion Multiplier Pattern Method Retraction In the photo I start at 100% on the left and go 2 steps lower The second with 92% to 86% I think it's 96% What do you think? For the pattern method I...

Hello I printed again after the filament had dried, unfortunately without success I then checked the belts from the Z belt, one looked a bit broken, see photo I did the gantry squaring again, but exactly as before Z Belt and A/B Belt checked for tension Input Shaper remade Bed Mesh looked at is...

OK I had Can you see that in the first pictures or just now? Can you give me a tip as to what exactly I should look at?

Hello What do you mean exactly At first I left everything on the Voron standard profile except the filament diameter and the temperature start code and end code The fan was also off