VORON Design

Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members!

Recent content by Rhoobarb2005

  1. R

    New 3D Printer User Seeking Help

    Well, I have hit another issue (shock!). The bed doesn't want to heat up. I checked the power, Motor Power has 24v, POWER has 24v, BED-Power has 24v, but BED-OUT does not have anything. I tested it via SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=60 and just setting the temps in the...
  2. R

    New 3D Printer User Seeking Help

    Thank you so much for the kind offer, I will keep that in mind. I'm in the UK btw. But... It seems that I don't need it!! I remade the wire between the tap sensor and the SB2099 and lo and behold, it works! So, in all honesty, I don't know what is going on with it because it says optotap on...
  3. R

    New 3D Printer User Seeking Help

    Thank for the responses. So, prgress has been made. Of sorts. On y, I removed the TMC and checked, all the jumpers are correct. I swapped the TMC with the one on motor 8. Now y moves! So the driver was either not seated properly or was faulty, it seems. In the end I just ditched the physical...
  4. R

    New 3D Printer User Seeking Help

    OK, so x seems to be functioning properly. The value needed was 166. I am not sure why it wasn't affecting anything before, although I did reset some of the other settings I have been tinkering with. It will now go all the way to the right, stop, and then let me adjust the distance + and -...
  5. R

    New 3D Printer User Seeking Help

    Ah, Ok, unfortunately tap has always been TRIGGERED. I'm guessing it's a cfg issue I haven't got to yet. I was just working my way down the list. No, if I press Home, it zooms from left to right, hitting the right side, then making a ratcheting noise to try and continue for about 3 seconds...
  6. R

    New 3D Printer User Seeking Help

    Thanks to all for the asnwers, again. I do appreciate the help. So, I have made some progress. I am now getting: EndstopSTEPPER_XOPEN EndstopSTEPPER_YOPEN EndstopSTEPPER_ZTRIGGERED ProbeTRIGGERED My only concern is it may be false reporting x. Because x will now move on home, but it hits the...
  7. R

    New 3D Printer User Seeking Help

    Thanks for the responses. I didn't realise the pins would pop out, so will give that a go. Some of the connections, although working, could do with being recrimped and remade, so the crimper wont go to waste. I haven't had a chance to redo the jst on the y, but I did change the printer.cfg to...
  8. R

    New 3D Printer User Seeking Help

    Sounds like a plan. I've ordered a crimping tool that includes Dupont and jst xh connectors. I'll do it properly. Although I will say, the switch must be making a circuit as the blue LED on it lights up when the switch is switched.
  9. R

    New 3D Printer User Seeking Help

    Ahhh. Sorry, I just thought Discourse was something within Discord. I'll try to.look onto it today after work. As for the congratulations, you may want to hold off the party balloons, it's not working yet. 😆 I don't know if skipping 4 years of knowledge and experience, is a good or a bad...
  10. R

    New 3D Printer User Seeking Help

    Again, thanks for the responses. I'll look into Discord. I have resisted so far, but I'll give it a go. This is my current printer.cfg # Manta M8P + CB1 + EBB SB2209 (CAN) [include mainsail.cfg] [mcu] canbus_uuid: e48efe7da441 canbus_interface: can0 [mcu EBBCan] canbus_uuid: a420eb1fbf59...
  11. R

    New 3D Printer User Seeking Help

    Well, I was only expecting the modifications to be that it ran Klipper. That was the whole description for the printer advert "Now runs Klipper", that was it. I googled what IKlipper was and thought "huh, that would actually be useful". It was only after I started trying to set things up I...
  12. R

    New 3D Printer User Seeking Help

    Hi all. Hoping someone can help a 'new to 3D printing' user out. We've been looking at getting a 3d printer for a while. We know Creality are fairly common and we wanted the biggest print size we could reasonably afford. So we found a used CR10 5S, where the advert stated: "Now running...
Top