Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members!
Update: after a lot of searching the wrong things on Google i ended up figuring out my questions i think,.
1st. yes, Spi-clk is the same as sck.
2nd. the jumper need to be all on bottom
hey again,
so im waiting for a new MCU spider v3 and i also decided to get some TMC2240 drivers(they got here today), now i didn't do enough research before buying since i thought drivers were somewhat plug and play, turns out they aren't.
therefore i am again asking for your help.
the driver is...
This works:
but i could not get that to work WITH CANBOOT, so i decided to use CAN on toolhead only, since toolhead is easy to flash without CANBOOT, but the spider board sucks to flash, tbh the spider board to me is just always a struggle to flash(atleast that is where i think my problems...
the spider extender, to my knowledge, came out before klipper had the usb to can bridge function, so before that you needed a usb to can adapter or can-hat for the pi.
Now i havent used usb to can bridge, but from my understanding you connect the extender with the ebb board toolhead and the...
sorry i havent replied before now, busy with work.
i have the v2 pcb that accepts 5-24v, but i just noticed that the blue led doesnt turn on, the red led just goes out when probing.
This is my toolhead board
https://wiki.fysetc.com/SB%20CAN%20ToolHead/#22-connectors
i was told to use IN.0 for...
Im going to follow this, i got my canbus working without can boot but, i would like can boot for easier flashing the toolhead.
You seem to be stuck where i got stuck as well.
Buuut now that i am running without can boot i just thought of something, the canuuid is that hardware specific or does...
How many probe points do you have for bedmesh? I think my mesh is too large (8x8 points) and that is where it F up with textured pei, i guess tap is tooo precise? And gets the valleys of the texture?
Yes, my problem was i could not figure out can boot, everything works now.. Canbus wise that is :p since i switched to tap i havent had a succesfull first layer, but I am slowly working towards that :)
update:
so i havent gotten it/everything working yet, but im making progress and learning.
so i took a look at the BTT U2C it wasnt bricked, i just didnt know what i know now, i thought it was stuck in dfu mode, long story short, it is working, and flashed now. i also dropped canboot since i...
hi,
thank you, that is great to hear :D
i have already spent a couple of hours today, so im currently taking a break.
i dont know why, but i didnt realize that it wont accept usart with usb can bridge... im tired i guess :P
i want to do some upgrades but i have gotten stuck.
controller board is a Fysetc Spider v2.3
for the upgrade i got a "canbus expander for spider" and "SB CAN TH"(stealthburner CAN toolhead)
i have to be honest, im not sure where i am at now.
i got a BTT U2C v2.1, since i thought i needed it, but...
thank you again ah2049, the problem is now solved :D
i swapped the driver, same issue, so the drivers are good, after that i tried turning the motor by hand still very hard to turn(both powered and unpowered), then i unplugged the motor (printer powered off ofc) and tested the wires had...
after looking at it more earlier today i can say it isnt completly locked up, idk when turned on, but when it is off i can rotate it but it is much harder to turn, compared to the other once, so i guess the motor is somewhat dead.
I dont know why i didnt think of switching the drivers, thank...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.