What's new
VORON Design

Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members!

Recent content by tianyi7250

  1. T

    Question Heater extruder not heating at expected rate,why?

    Sorry, my English is not very good. What you mean is: There's a break somewhere in the wire at the hot end (the thermistor or heating block)? Your test is to heat the hot end and then move the print head by hand to see if it will stop? I executed the command: PID_CALIBRATE HEATER=extruder...
  2. T

    Question Heater extruder not heating at expected rate,why?

    An error occurred when printing the model today. This is the klippy.log that I found. What's the reason for this? Thanks. (It seems that this error occurs approximately every one and a half hours.) I just checked the wires and the connectors. Opened the hot end and gave it a clean. But...
  3. T

    Question Which stl model is used for this hotend? I didn't find it.

    Which stl model is used for this hotend? I didn't find it.
  4. T

    Question Which stl model is used for this hotend? I didn't find it.

    thankyou. I was thinking about 3d printed models. stl for tz-4.0
  5. T

    Question Which stl model is used for this hotend? I didn't find it.

    Where can I find this hot end model? I can't find it. thank you
  6. T

    Trident printing structure with which filling strength is better

    I see the documentation says "Grid, Gyroid, Honeycomb, Triangle or Cubic" fill pattern. Sparse filling percentage 40% unchanged, then which of these filling strength is better? thank you
  7. T

    Which stand should BIGTREETECH TFT35 use and can it connect directly to the spider motherboard?

    （BIGTREETECH TFT35 SPI） I would like to interface my trident using this display. However, I am uncertain about where to find bracket model for it. Additionally, can this display be directly connected to the spider v3.0 motherboard without io2can? Thank you.
  8. T

    Which stl model is used for this hotend? I didn't find it.

    thank you
  9. T

    Which stl model is used for this hotend? I didn't find it.

    Which stl model is used for this hotend? I didn't find it.
  10. T

    I remember there was a multi-color extruder on voron's website before, how come I can't find it now?

    I remember there was a multi-color extruder on voron's website before, how come I can't find it now?
  11. T

    Has Trident been renewed in the last year

    I want to build a Trident Was there any major renewal of Trident this year? If there is, I want to wait. Just assemble the new version, so you don't have to upgrade it thankyou
  12. T

    Unknown command:"TEST_RESONURS", why?

    Why "unknown command"?
  13. T

    Question The value of adxl345 z is always over 9000

    1. Thank you for your response. The ACCELEROMETER_QUERY has returned a z-axis value exceeding 9000, and I have utilized "MEASURE_AXES_NOISE" to obtain values ranging from 1 to 100. Would this be appropriate? Additionally, may I proceed with measuring resonances? thankyou
  14. T

    Question The value of adxl345 z is always over 9000

    I installed adxl345 on voron 0, But it turns out that the Z-axis is always more than 9000 values What is the reason for this?
  15. T

    Do the Raspberry PI 3b and pico need separate power for usb connection?

    Connect the Raspberry PI and pico motherboards using usb. I read in the pico manual that using a usb connection requires powering the Raspberry PI separately, is that right? (Red circle on the picture) I see the voron0.2 pdf does not say that this connection also needs to be powered...
See more
Top