Recent content by Vorkosigan

Which extruder do you have? Galileo 1 or 2? For Galileo 2, I just printed the files from the galileo 2 github and it just worked with tap. (For reference, I am using Vitalii's CNC tap, but I think it would be the same for printed tap)

You are looking for rotation distance. https://ellis3dp.com/Print-Tuning-Guide/articles/extruder_calibration.html A couple of thoughts, I don't know what extruder or stepper you are using, but double check the gear ratio and the steps per rotation are correct.

I had an issue recently where my raspberry pi on my V0 suddenly stopped connecting wirelessly. Wired was perfectly fine. All of my other wireless devices were fine. Tried other raspberry pi's and none of them worked either. No changes to my network. It took a few weeks for me to finally actually...

For the exclude object errors, my guess would be that setting is turned on in your slicer, but not in your klipper config? Probably not your MCU shutdown problem, though.

The ones that slide under are for the special nuts that can be added after the V0 is built. Not sure if they would work for a normal square nut or not. I think this is what you are looking for https://github.com/MotorDynamicsLab/LDOVoron0/blob/v02/STLs/Slide_In_Nut_Support/Slide_In_Nut_Support.stl

I'm gonna answer my own question a little bit here. If any info is wrong, feel free to correct me. I ended up switching to some white leds from adafruit for the nozzle lights. RGB isn't really necessary there for me. (Actually, I only got the RGB sequins because I didn't know about the plain...

Decided to switch to plain white led sequins for the nozzle lights. Didn't really need to the RGB there anyways and that should simplify wiring. These are the Adafruit sequins and I believe 5v. Can I still use the RGB port on the ebb36 for them? (Only need 5v and dc ground, but still need the...

For my second question, would it be as easy as using the x and y endstops for signal and ground (going sensorless homing so those would no longer be needed) for the matchsticks and the neopixel pins for the kirigami neopixel and then share the 5V neopixel between all 3?

I'm in the middle of my V0 rebuild and upgrade and have a couple of questions on the wiring that I have searched for answers and not found much information at all. I have some neopixel sequins for the mini stealthburner and I am using the ebb36 can board. I am assuming the I can use the RGB...

Are there any better panel clips for the V0? I don't think I've looked for those yet.

For me, I found that I didn't feel I could pluck consistently enough to be accurate, not so much that the idea of it was inaccurate, if that makes sense. I would probably be interested in something like this.

https://www.amazon.com/dp/B099NPWSFB This is for the bowden tube going through the foot where the switch being used as a filament sensor is. I did not need a 50 pack, but I figure I am all set if I decide to build an ERCF at some point. Edit: Also needs an MR85 Bearing. It does not appear that...

I've been printing mostly abs with a little tpu thrown in. In the past I mostly printed petg. I have not done any of the filled filaments yet because i just haven't had a use case for them. I don't think I am quite at the point where I need the metal parts, but I am still deciding on the...

majic79, yours definitely sounds similar to mine. 2. https://www.amazon.com/Printer-Accessories-Voltage-WS2812B-Printer/dp/B0C77BXGRZ/ I am thinking these for the lights? 3. https://www.amazon.com/gp/product/B0C5D97DRJ/ There seems to be a few different version of these pi cameras. Not sure...

10. Pros and cons of an MGN9 rail for X? Edit: Decided to just go for an MGN7 with a higher preload. Just to be clear, I have at various times searched for the answers to these questions, but I either didn't find any information, didn't find enough information, or ended up with analysis...