Recent content by Dickdasty

Hi guys i have an issue with selector , suddenly i received this message "MMU issue detected whilst printer is paused Reason: Homing selector failed because of blockage or malfunction. Klipper reports: No trigger on mmu_sel_home after full movement" Who can be ? "Endstop MMU_SEL_HOME" works well

Hi i'm just resolved now : And there was light ...! So @ the end : with SD card Nok but in DFU mode following all steps Power off add 2 jumpers : boot and USB 5v Power on and push reset button lsusb Bus 001 Device 016: ID 0483:df11 STMicroelectronics STM Device in DFU Mode cd ~/klipper make...

Hi guys i'm fighting with a mistake done during installing MMB board for ECRFV 2 I dont know what i've done but now my Voron Trident dont boot : show message mcu 'mcu': Unable to connect. I followed a lot of guide how to reload klipper on MCU but i a have still issue . Voron Trident 300 Octopus...

Hi guys, i'm building an ECRF v2 Siboor Kit for my Trident 300 mm I'm on the first phase and i found a lot of difficult to assembly the filament block . I don' t understand the meaning of "Base_Trap_M3" that every time i broken when i assembly the entire block . I tried to modifidy shape of...

Ciao NoGuru , what are you seeing is a comparison between my Voron Trident and a professional printer 3DNT A2 . Are two differents world but in any case are comparable.

Hi Guys my Voron Trident has lost good setup that I had laboriously found . My setup is : Stealthburner with LDO Lite v2 extruder + Rapido 2 hotend 0,4mm nozzle, Slicer Superslicer with Ellis setup. Materiak , ABS + esun (and other Plymaker) I lost me z-offest and now I'm struggling to get...

Hi Laser i have (had is better) resolved my issue replacing type of PTFE . Before i had a tranparent tube from un-know supplier (id 2,2mm) but with lower quality . After a lot of test i replaced old one with one of the Capricorn (id 2mm) with any problem . Never a stop or clogging. I also added...

Hi guys i'm struggling with clog of mine Rapido2 HF on Stealthburner . Head is composed with extruder Lgx2 Lite and Rapido 2 Hf . I've had replaced fan hotend and now i've implemented macro for unload wire because still remain clog in heatblock mainly or in the Heatsink Clogging occurs when i...

Hi guys is from some days i'm seeing an issue on my Stealthburner head with Rapido 2 HF . When i heat the hotend happens it take longer time to reach the target temperature and then start to smoke ! After that Klipper shutdown my printer and appear this message : What can it be ? Thermistor...

Hi Claude yes is what looking for !

Hi guys how is the best way for add a material in superslicer ?

Hi guys. I've followed your adivse and i re-done step calibration and SLicer Flow rate . Seems better , what do you think ?

Hi ClauderMilk , I done tuning of SuperSlicer and Ellis flow rate . I think that test of SuperSlicer or my results are not reliable and some value is not right . Just tonight i re printed with cura and results was not so bad .

Hi guys . About extruder step calibration is one of first calibration done but i can recheck . So in any case i done other tests and i try a good solution using Cura as slicer and update the Z calibration with +0.05 . What do you think ?

Hi guys, i'm fighting with my voron trident 300 . My setup is : Voront trident 300 - formbot kit , no canbus , extruder Lgx lite v2 + hot end Rapido 2 Hf . Material : Polymaker PLA , temp Hotend 210° and bed @ 60° Slicer SuperSlicer with Ellis Profiles and main calibration done . I replaced my...