Recent content by Dr.Who12

Thanks. I got it and found some steps I missed the first time I set it up. Works fine now.

I'm guessing that was directed to me. Yes there is a reason. Tap takes forever to map the bed and honestly it isn't that accurate. The Cartographer 3D doesn't touch the bed and I can map the entire bed in about 20 seconds. I've also enjoyed better prints, well at least until they updated...

A few days ago I noticed that I had some updates for my Voron. I proceeded to do all of them and after they were done, Klipper rebooted and it came up with an error about a depreciated setting. No worries. But then my Cartographer 3D told me I needed to recalibrate the sensor, so I did. Now...

Did you ever get it working? Voron2.4R2 Pro+ with BTT Manta M8P + CB1, EBB SB2209 CAN and all the upgrades. Mine was a little difficult but it is up and running now with a Cartographer3D Z instead of TAP.

For those of you who have had issues with the filament pulling back on the extruder because of the way it is routed, I modified mine to eliminate that. The standard hole in the rear of the enclosure seemed to put undue stress on my Stealthburner to the point I actually saw it actuate my TAP. I...

Can you specify which Cartographer 3D product you purchased and any accessories required to mount or wire it to your SB2240? I'm looking to do the same.

Sad thing is I have that document and never saw that configuration in there. Thanks for pointing that out. I've downloaded so many different documents while putting this thing together, I've lost track. Let me try that and see if that works. The issue was all I was finding on the internet...

Hello all, Before I ask my questions, I'm going to include a link to my printer setup. It is the completely maxed out version on here: https://www.3dprintersbay.com/voron-2 I am looking for the correct setup configuration for using TAP to do bed meshing. I've found some instructions but...

Still have errors but here is my printer config file along with a klipper log. Log is at the top, config at the bottom.

Finally after reprogramming the canbus and the EBB SB2440 I have it working. Now I just need a valid printer configuration file for my setup. I found a couple but they are not exactly what I need but I will get it working eventually. I'm almost finished putting it together so hopefully I can...

Hello everyone. I'm seeking assistance with programming for my new printer. Something is not right and I can't seem to figure out what the issue is. My main board is a Bigtreetech Manta M8P+CB1 V1.1 and Canbus BTT EBB SB2240 CAN. All wires and jumpers are placed in their correct respective...

So I was able to figure out some of the wiring on mine last night. I suggest purchasing (https://www.amazon.com/gp/product/B078WPT5M1/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1) to crimp the new connectors on. Going back and forth between vendors like BTT and Voron with their install...

STL files: https://drive.google.com/file/d/11nKZk7vjYy9ADPq-8vDks7oAebybWieG/view?usp=drive_link Wiring diagram: https://drive.google.com/file/d/1Cq7LWvDv7ZkAo8UH1fZQUC-eRevE1t4u/view?usp=sharing Other instruction...

After reaching out to the vendor, they supplied me with some documentation. It was helpful, however there were some steps that were in the instructions that did not apply. (like removing some extra print material on one of the pieces that actually kept the belts facing forward. Overall between...

Thanks. I'm stuck now, even missing printed parts that I paid for through 3DPrintersbay which is actually Formbot3D. Guess I'll have to wait until they are finished with Tomb-Sweeping day in China to ask them for help.