Recent content by Zephyrus67

Yeah I dont feel either it will affect funtionality. I am just wondering what it is from. That seems to me as a different issue though. I dont have that issue with the whole of the inside of the printer being covered and I dont really have issues other than this stuff attaching to where I...

Hello All. I have been noticing that I have some white powder sticking to my hotend fan and also found some of it around the center LED of the toolhead (Stealthburner) (Attaching some images). It does not seem to me like dust but more like chalk/calsium 'ish'. This is something I have noticed...

Yesterday I ran into a wear issue after I started a print job. I am using a Voron 2.4 R2 with EBB 2040 can board and ERCF v2 using the old EBB Burrow board + Voron tap. After the printer was done with all the initial things (QGL+bed mesh+scrubbing etc.) and started on the real print it started...

The 4 pin max31865 thermistor connector supports PT100 and PT1000 thermistors, but does anyone know if that indicates that it ONLY supports those 2 or is that extra so it also supports NTC Thermistors?

Yes everything you write is also how I actually thought it should be. I DO clean the brush between each print. Automatically with a brush and bucket system but also manually if I can see it is needed. I also changed the retraction settings after end print and in the brush/bucket system to make...

Hello I have now been using my Voron 2.4 R2 for a while and have become happy with it and its results. There have been some issues/challenges over time especially with adhesion but that seems to have been solved. One of the major upgrades I did to my setup is the Voron Tap + Stealthburner and...

I have been strugling with a weird situation the last day or so. A week ago I ordered 4 ADXL345 accelorometers on amazon. I mounted one of them while looking in the docs for klipper. I mounted it all correct and got it all up working. I did a full ressonance test and entered the values into my...

I was uploading a gcode file set for my ASA material. It was sliced with 255 hotend temp and 110 bed temp. After it was half through the print I noticed it was curling the prints on overhangs and decided to re-slice with lower temps at 240 / 105 I saved over the existing file. Deleted the one...

I have not tested that yet. I need to find the information about which pins to measure on when it is 2209 drivers.

I already did that....I have had all Z motors completely dismounted and placed them on the table but with the JST connectors still connected. And when activating Z in mainsail the motors still makes noise.

Yes but I guess PEI sheets can also come in monday/friday copies :) And yes scrubber works with tap. I Installed the decontaminator scrubber last night and it works. I rewrote the macro though. It seems like the macro he made forces 240C for it to be able to purge. I also still have left to...

I would not even start working with the smooth side having issues with the textured side :) Anyway...I have been done more testing....I managed to get the front for my stealthburner printed. It took 255C nozzle temp and 115C With the ASA I usually print from 235C and 100/105C on my vyper...that...

@claudermilk Did you have a stepper issue as well or did I read that wrong? Yes I have also already tried all kind of cleaning the printer surface dish soap, IPA and even a bit of acetone to see if that would degrease the surface. I have not been sanding the PEI sheet yet since I assume that...

I have been ongoing with testing this and that but still without being able to make a successful print with ASA (even though I was able to do 5 prints with ASA right when I started the printer up at first). I did the Ellis Tuning thing but that made everything worse. My gantry that was perfecly...

Back to testing with ASA at bed temp 110C After moving back to testing again with ASA I need to adjust my z_offset to be 0.1 lower than for PLA. Is this normal? I thought the whole idea of the Voron Tap was to avoid things like this....