Decked out Voron - Going all in

[Ch3vr0n]

This is a copy of my reddit post since they pointed me here too.

So after rebuilding my old CR10 max into a klipper based printer. It's time to let it go in about a month when final budget is obtained hopefully soon after. Watched plenty of Canuck Creator (u/ubernero) and 3D Musketeers (u/mobius1ace5) and the decision has been made to build a decked out "balls to the wall" Voron 2.4 350. And i do mean "balls to the wall" no budget restrictions toolchanger. Unless Bondtech INDX comes out between today and beginning of january it'll likely be stealthchanger based. The actual build will be in stages: Stock kit barring switching out the control board/screen/psu immediately > Toolchanger setup but single tool > multi-tool

So far the decision has been made for

• Kit will be an LDO Voron 2.4 350 RevD from 3Djake
• CNC Chaoticlab CNC parts unless i find an LDO kit within the EU
• LDO AWD kit perhaps?
• CPAP mod? ditched based on current feedback
• Stealthchanger 6 tool fits on a 350 afaik + tophat Toolhead settled: A4T x6
• Beacon on carriage
• Ditch the revo for Dragon HF or go straight for 6 chube compacts? Hotend Settled, Chube Compact x6
• BTT knomi's in tool docks! *Optional*
• Switch the CW1 extruder for high performance ones that can keep up with the hotend~~ Extruder settled, Orbiter v2.5
• recommended camera?
• swap out leviathan controller from the Rev D kit for a BTT Kraken
• Upgrade screen to BTT HDMI 7
• Orbiter smart filament sensors
• Doom cube frame kit
• Rigid panels (either 6mm PC or metal
• Upgraded PSU (LRS-600-24?)
• tophat and longer Z belts? do i need it with dragonburner?
• 48V steppers on X/Y/Z but which ones
• boxturtle + enclosures on each tool for whopping 24 "tools" if possible. Go nuts!

Any remarks? Am i missing anything? Yeah i'm nuts for a 1st voron

PURCHASE REGION: BELGIUM (EU)

 

[5twenty]

ACM panels are awesome, get those, unless you have something beefier in mind.

AWD? - nvm, I see it...I would like to do this mod as well.

Skip Chaoticlab's stuff, hit or miss, though I've had more hits than misses.

Why swap out leviathan? I hear it's good, and they have expansion boards now....

Orbiter...you can use Wristwatch or Galileo 2 with filament runouts, to save a little coin, but your choice.

Screen...I am removing all mine, I just don't use them enough with Klipper machines. I can carry my phone/laptop and use it for moves I need to make while at the printer. But they are nice to look at.

Knomi...I'll be doing the same, I like these little screens.

Tophat shouldn't add much Z to your build, unless you are specifically add more Z somehow...would require new upright extrusions cut right to increase Z...unless I am missing something in your comment?

I like the plan. Indeed, do build it stock first and shake out any issues, then mod it. Though...frame, AWD, tophat, etc (things that require preloaded nuts...) I would do as I build it stock...it sucks tearing it completely down to rebuild, especially since the frame pieces, and non-mechanical-moving parts, won't affect the performance...much.


Good luck, I miss living next to you...but one day I'll return to Benelux and be happy.

 

[Ch3vr0n]

I'd love to do an LDO CNC kit instead of chaoticlabs. I just can't damn find it, that's the problem. Why switch the leviathan, well i wouldn't be going all out if i didn't Filament sensor setup hasn't been fully decided yet, and would be simple to do with a single tool, on a multi tool i'd need spots for 6 different runout sensors. The simplier the setup in that regard probably the better, what's more simple than sensors that mount directly on the extruder? Screen might ditch it. Might not. I can always re-use it for a homeassistant setup.

Top hat isn't much about the adding z-height, it's more "do i need it to avoid losing z-height build volume with the Dragonburner toolhead".