VORON Design

Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members!

Recent content by George Velkov

  1. G

    Temperature chamber question

    I can't figure out what kind of isulation you're talking about. How should it be isolated and with what. I have spent many hours on the web looking for information and the printers I have seen with panels of transparent material, and I couldn't see a printer with isolation I want to make this...
  2. G

    Temperature chamber question

    Thank you very much for the information Sandman50 And what temperature should be maintained in a camera when printing with ABS Regards, George
  3. G

    Temperature chamber question

    Thanks again for the quick reply but things are going to get a bit complicated as I have to manage and more lights, Nevermore filters and MMU for color printing - ERCF v2 I will probably need additional MCU ports. I have the idea to use a Raspberry Pi Pico to the main raspi that I use -...
  4. G

    Temperature chamber question

    Thanks for the reply, but I would like to know what temperature sensors are used, where is the best mounting location and how does the Klipper control and maintain the set temperature.
  5. G

    Temperature chamber question

    Hello, Can anyone share what hardware and software changes are required to maintain a certain temperature in the Voron Trident box. Thanks in advance Sincerely, George
  6. G

    Bed mesh calibration - question

    I can't do better than that. What could be the reason?
  7. G

    Bed mesh calibration - question

    I don't use Windows Notepad. I edit with either Notepad++ or Visual Studio Code
  8. G

    Question Config of the Stealthburner Leds

    The configuration of my printer is as follows: - Printer Voron Trident - 250 - MB - BTT SKR 1.3 + additional driver for the 6th motor. UART management - Raspberry pi 3+ - Stealthburner with three neopixel diodes without CAN buses - Step motor drivers A4988 for tests.On TMC2209 finalization - Z...
  9. G

    Question Config of the Stealthburner Leds

    Thanks. Thanks a lot and to all who helped me to solve the problem with Stealthburner toolhead lights. George
  10. G

    Bed mesh calibration - question

    Of course. I have translated most of the comments into BG, but I don't believe this will interfere.
  11. G

    Bed mesh calibration - question

    Hi majic79, thanks for your comment. Not working [gcode_macro PRINT_START]. Klipper throws an error: Source contains parsing errors: '/home/pi/printer_data/config/printer.cfg' [line 429]: 'G28\n' [line 430]: 'Z_TILT_ADJUST\n' [line 432]: 'G28\n' Option 'bed_mesh_calibrate algorithm'...
  12. G

    Bed mesh calibration - question

    Hi, I tried to check the printer bed and after the command - CALIBRATE, I got this picture, but I don't know if it's good. I am asking for your opinion and is there anything I should do Thanks in advance George
  13. G

    Question Config of the Stealthburner Leds

    Of course I will try I placed the entire [neopixel sb_leds] block in the printer.cfg file. There is no difference in the behavior of the lights. It is the same.But after finishing the printing and when the head goes to the home position, Klipper prints some error that I don't understand and I...
  14. G

    Question Config of the Stealthburner Leds

    Hi, It's the first thing I've done. The file has the extension *.cfg. With extension *.txt is only for the forum as files with extension *.cfg are not accepted. "print.cfg" file has been updated with stealthburner.leds.cfg Here are some screenshots of my machine. Greetings, George 73! LZ1GBY
  15. G

    Question Config of the Stealthburner Leds

    I don't think it's a hardware problem, but anyway, Thank you very much for your responsiveness and attention. When manually manipulating the blue buttons, all commands and light combinations are executed accurately. I also did a test by reconfiguring another port from the MCU. The result is the...
Top