Recent content by BOSSJoe

I did something similar at the end. I started at 120 and then went down to 100, then in steps of 10 down to 60 and then to 58. As I said, I have very little experience with sensorless homing and I was unsure when I went that low. But now I've learned something again. Not bad either. Joe

Perfect, thank you very much. After a little sleep and a little more thinking, I came up with it. The problem with my understanding was that I had to go quite far down with the values. I started at 255 and then went down in steps of 50. I think that's what the instructions say. When I got to...

Hello everyone, I could use your help. I can't see the wood for the trees. I'm currently building a formbotkit of a Voron 0.2 and am in the process of setting up the printer.cfg. Unfortunately I have some problems with the sensorless homing. I think this is because I have built a wild mixture...

Okay switched gears for now and used the following: GND and GPIO16 from the E0-Stop for GND and Encoder 5V and GPIO29 from SERVOS for 5V and Switch Switch is working fine. I see the red light when no filament is loaded and in Klipper it shows as "Empty". Encoder light is blue blinking when...

Hello, yes I have. However, the SFS v2 requires a total of two pins, GND and 5V. I first connected this to the "laser" and "E0-Stop" port. But that didn't work at all. Every time I loaded filament, the board restarted. Greetings Joe

Hello, I haven't found anything official on this either. I had hoped that one or the other port could possibly be used for a different purpose. Unfortunately, I'm not quite up to speed on the subject and I don't want to destroy the board or the sensor. I actually wanted to stick with the Pico...

Hello, I have bought two SFS v2 and would like to connect one of them to an SKR Pico board which is installed in my Voron 0.2. Is there an official way to do this? I couldn't find anything in the manuals. Thank you very much Greetings Joe

Hi There, @NoGuru There's nothing really wrong with the old feet. The only thing that bothers me is that the flap on the underside for the electronics always gets stuck on the feet. That's always a bit fiddly. Otherwise no problem. Maybe that I like the new feet a little better :-) Regarding...

Hello everyone, I have a question. I've done a lot of searching online but to be honest I've found so much information that I'm now completely confused... :-) I currently have a Voron 2.4 R1 with a few minor modifications (AB-BN, Nevermore, LED,...). This means that I currently still have the...

Hello, please excuse the late response from me. I was a little busy with work... I think I have made up my mind. It will be the Formbot kit with their print parts. They are supposed to be quite good and the price is very interesting. In general, I'm going to build the printer from scratch, but...

Hi, Thanks for your assessment. I also went to my Voron 2.4 with this setting. Build the thing stock and see what you can change or improve. Unfortunately this led to a lot of try and error, a lot of wasted money and time and a lot of parts lying around. I don't want to talk about the many...

Hi Forum, I need your opinion or help. After my Voron 2.4, I would like to build a Voron 0.2. This time I would like to use a kit. I sourced my 2.4 myself, but unfortunately I don't have the time. And here comes my first question: Which kit is best for me? 1. Formbot 2. Fysetc 3. Siboor 4...

Thank you so much. I will have a look.

Hi, okay that's what my research already showed too. Just set the whole thing up as [fan generic]. Do you still have it temperature controlled or do you do it all manually? Thanks a lot Joe

Hi together,maybe you can help me. I think I just do not see the forest for the trees... I have in my Voron 2.4 a total of 4 different fans: - Parts fan - Extruder fan - Controller fan - Nevermore fan The parts fan I can set via the Mainsail Gui how fast it should rotate. Can I possibly do the...